crankshaft sensor position

crankshaft sensor position

This is a discussion on crankshaft sensor position within the Evoque Maintenance forums, part of the Land Rover Evoque Garage category; Hi, I have changed timing chain on my 2011 pure drive rangerover evoque si4 and remove crankshaft position sensor without mark theposition, now I have ...

Page 1 of 4 1 2 3 ... LastLast
Results 1 to 10 of 37
Like Tree1Likes

Thread: crankshaft sensor position

  1. #1
    Junior Member
    Member #
    9329
    Join Date
    Jan 2017
    Posts
    4

    crankshaft sensor position

    Hi, I have changed timing chain on my 2011 pure drive rangerover evoque si4 and remove crankshaft position sensor without mark theposition, now I have loose the good position and my car show error code p0016and p0017, please somebody can say me what tooth fact face to crank sensor whenthe engine is on TDC thx
    Last edited by Rsquared; 01-18-2017 at 08:24 AM.

  2. # ADS
    Ads


  3. #2
    Super Moderator
    Member #
    1235
    Join Date
    Dec 2012
    Location
    Canal Fulton, Ohio
    Posts
    500
    Lasha, Welcome to the forum! I edited your post to change the font color to white, so it was more readable.

    Sounds like you are in a bind, sorry for that. You need to get a service manual for the Ford 2.0 EcoBoost engine. After market service manuals for a Range Rover Evoque are hard to find. A Ford manual might be easier to come by.

    Good luck!

  4. #3
    Junior Member
    Member #
    9329
    Join Date
    Jan 2017
    Posts
    4
    thank you rsquared, i will try that

  5. Remove Advertisements
    EvoqueForums.net
    Advertisements
     

  6. #4
    Super Moderator
    Member #
    1235
    Join Date
    Dec 2012
    Location
    Canal Fulton, Ohio
    Posts
    500
    Lasha, I have sent you an e-mail with the procedure from the Range Rover factory service manual, on how to install the crankshaft position sensor.

    Let us know how you make out.

  7. #5
    Junior Member
    Member #
    9665
    Join Date
    Mar 2017
    Posts
    2
    Good day. Its my first time on this forum. I also need some assistance. I have a Range Rover Evoque si4 and have removed the crankshaft position sensor without marking the position of the tooth on the trigger wheel that is facing the CKPS. After I removed I noticed that the sensor has a slot instead of a hole. Please advise on how to adjust the sensor as I am now getting a P0017 camshaft and bank 1 camshaft correlation error code.

    Please assist

    GTkhali

  8. #6
    Super Moderator
    Member #
    1235
    Join Date
    Dec 2012
    Location
    Canal Fulton, Ohio
    Posts
    500
    GtKhali, Welcome to the forum.

    If you PM me your e-mail address I can send you some pictures and a write up from the Factory Service Manual on how to correctly install the Crankshaft Position Sensor. You do need a special tool. I have seen the JLR-303-1595 Alignment tool, Crankshaft Damper, advertised for around $50.00.

  9. #7
    Junior Member
    Member #
    9665
    Join Date
    Mar 2017
    Posts
    2
    Thank you for the feedback. My email is [email protected]

  10. #8
    Super Moderator
    Member #
    1235
    Join Date
    Dec 2012
    Location
    Canal Fulton, Ohio
    Posts
    500
    GtKhali, I sent you an e-mail with the procedure for installing the crankshaft position sensor.

  11. #9
    Junior Member
    Member #
    10529
    Join Date
    Jul 2017
    Posts
    2
    Quote Originally Posted by Rsquared View Post
    GtKhali, I sent you an e-mail with the procedure for installing the crankshaft position sensor.
    Hi Everyone. This is also my first time on this forum. Similar to the rest I also need some assistance from everyone. I just purchased a Range Rover Evoque Si4 with a P0016 & P0017 error too and the previous owner told me that he had changed the pulley before and then these fault codes came out.

    Can anyone here help me out please?

  12. #10
    Super Moderator
    Member #
    1235
    Join Date
    Dec 2012
    Location
    Canal Fulton, Ohio
    Posts
    500
    Super2ndgen, Welcome to the forum!

    If you want to PM me your e-mail address, I will forward the e-mail I sent to GtKhali with sections of the Factory Service Manual, for installing the crankshaft pulley. If you need to reset the crankshaft pulley, you will need a Land Rover special tool, which is listed in the e-mail.

Page 1 of 4 1 2 3 ... LastLast

Ads

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. Crankshaft trigger Position
    By apigo200x in forum Evoque Forum
    Replies: 0
    Last Post: 01-08-2017, 02:31 PM
  2. Aux Ignition switch position...
    By Starflyr in forum Evoque Forum
    Replies: 9
    Last Post: 04-20-2015, 11:49 AM
  3. TMPS Sensor question?
    By redrover in forum Evoque Forum
    Replies: 3
    Last Post: 05-08-2013, 07:49 PM

Search tags for this page

crankshaft mail
,

evoque crankshaft sensor code

,

how to remove and install a 2012 range rover evogue crankshaft sensor

Click on a term to search for related topics.
Find us on Google+
 

SEO by vBSEO ©2011, Crawlability, Inc.